Circuit : Andy Collinson
This circuit is used to relay signals from an Infra Red remote control in one room to an IR controlled appliance
in another room.
I have seen these devices advertised in magazines, they sell for around £40-£50 and use radio to transmit between receiver and
transmitter. This version costs under £5 to make and uses a cable connection between receiver and transmitter. For example, if
you have a bedroom TV set that is wired to the video or satellite in another room, then you can change channels on the remote satellite
receiver using this circuit. The idea is that you take your remote control with you, aim at the IR remote control extender which is in
the same room, and this will relay the IR signal and control the remote appliance for you. The circuit is displayed below:
1 SFH2030 Photodiode
1 TIL38 IR emitting diode
1 5mm Red LED
2 4.7M 1/4W resistors
1 1k 1/4W resistor
1 2.2k 1/4W resistor
1 27ohm 1/2W resistor
1 BC337 transistor
1 CA3140 MOSFET op-amp
The CA31340 is available in the US from Electronix Express, part number N103140.
|DigiKey Part Numbers
Some parts may not be available in the United States. Special thanks to Dave Mains who has provided equivalent parts in the table on the
left from component supplier Digikey. Maplin Electronics do not supply to the united States.
The advantage of this design against similar designs is that there are no adjustments to make or set-up procedures. However care should
be taken to avoid ambient light reaching the photodiode. A daylight filter type (black in colour) is recommended. Bellwire or speaker cable
may be used to remotely site the IR emitting diode, since this design uses low output impedance and will not pick up noise. Some systems
require coaxial cable which is expensive and bulky. The wireless variety of remote control extenders need two power supplies, here one is
used and being radio are inevitably EM noise pollution. A visual indication of the unit receiving an Infra Red signal is provided by LED1.
This is an ordinary coloured LED, I used orange but any colour will do. You will see LED1 flash at a rate of 4 - 40Hz when a remote control
button is pressed. LED0 is an Infra Red Emitter Diode, this is remotely wired in the room with the appliance to be controlled. I used the
type SFH487 which has a peak wavelength of 880nm. This is available in the UK from Maplin Electronics, order code CY88V. Most IR remote
controls operate at slightly different wavelengths, between the range of 850 - 950nm. If you cannot obtain the SFH487 then any IR emitter
diode that has an output in the above range should work.
About IR Remote Controls
As previously stated IR remote controls use wavelengths between 850 - 950nm. At this short wavelength, the light is invisible to the human eye,
but a domestic camcorder can actually view this portion of the electromagnetic spectrum. Viewed with a camcorder, an IR LED appears to change
brightness. All remote controls use an encoded series of pulses, of which there are thousands of combinations. The light output intensity
varies with each remote control, remotes working at 4.5V dc generally will provide a stronger light output than a 3V dc control. Also, as
the photodiode in this project has a peak light response at 850nm, it will receive a stronger signal from controls operating closer to this
wavelength. The photodiode will actually respond to IR wavelengths from 400nm to 1100nm, so all remote controls should be compatible.
The receiver is built around a silicon photodiode, the SFH2030 available from Maplin, order code CY90X. This photodiode is very sensitive and
will respond to a wide spectral range of IR frequencies. There is a small amount of infra red in direct sunlight, so make sure that the diode
does not pick up direct sunlight. If this happens, LED1 will be constantly lit. There is a version of the SFH2030 that has a daylight filter built
in, the SFH2030F order code CY91Y. A TIL100 will also give good results here. A photodiode produces minute pulses of current when exposed to infra
red radiation. This current (around 1uA with the SFH2030 and a typical IR control used at a distance of 1 meter) is amplified by the CA3140
op-amp. The op-amp is configured as a current to voltage converter, producing an output of about 4.7 volts per uA of input current. The
photodiode, can be placed up to a meter or so away from the circuit. Screened cable is not necessary, as common mode signals (noise) will
be rejected. It is essential to use a MOSFET input type here as there is zero output offset and negligible input offset current. A 741 or LF351
can not be used in this circuit. The output from the op-amp is amplified by the BC337 operating in common emitter mode. As a MOSFET op-amp IC
is used, its quiescent voltage output is zero and this transistor and both LED's will not be lit. The 1k resistor makes sure that the BC337
will fully saturate and at the same time limits base current to a safe level. Operating an IR remote control and pointing at the photodiode
(SFH2030) will cause both LED's to illuminate, you will only see the visible coloured LED (LED1) which will flicker. Remote controls use
a system of pulse code modulation, so it is essential that the signal is not distorted by any significant amount. Direct coupling, and a
high speed switching transistor avoid this problem.
No special PCB is required, I built my prototype on a small piece of Veroboard. The pinout for the CA3140 is shown below. Note that only the
pins labeled in the schematic are used, pins 1, 5 and 8 are not used and left unconnected.
Specifications of Prototype
No alignment is necessary in this circuit. The only thing to watch is that the emitting diode is pointing at the controlled device
(video, CD player, etc). I found that the beam was quite directional. Also make sure that there is a direct line of sight involved. It will not
work if a 5 foot spider plant gets in the way, for example. I had a usable range at 5 meters, but possibly more distance may be possible. As a
check, place a dc volt meter across the 27 ohm resistor. It should read 0 volts, but around 2 or 3 volts when a remote control is aimed at the
Having made my prototype, I ran a few tests :-
||60mA operating ( with 12V supply)
||85mA operating (with 15V supply)
|IR receiver range:
|IR transmitter range:
||> 5 metres
It is difficult to measure the IR transmitter range as this is dependent upon a number of factors. The type of infra red control used and its proximity to the receiving photodiode, the voltage supply, the wavelength and efficiency of the IR emitter and the sensitivity of the controlled appliance all affect overall performance.
The reception range of the IR remote control to the photodiode depends on the strength of the remote control, but I had a working range of a meter or so, this needs bearing in mind when placing the circuit. Its also a good idea to wire LED1, the coloured LED near to the photodiode, that way, you know that the unit has received a signal. The IR emitter has a larger range, I had no problems at 5 meters but may possibly work further distances. The emitting diodes
are quite directional, so make sure it is aimed directly at the appliance to be controlled. The IR emitting diode is small and can be placed out of sight. I drilled a small hole above the door frame. The emitter diode leads were insulated and pushed through this hole, leaving an inch or so to adjust the angle and position of the LED. From a distance, the clear plastic lens of the diode could not be seen.
Final Comments and Fault Finding
To date this has proved to be one of the most popular circuits on my site. Of all the email I receive
about this circuit, most problems relate to the Infra Red photo diode. You must make sure that this
is pointed away from sunlight, or use a type with daylight filter, otherwise LED1 will be constantly lit,
and LED0 will be in operation also. This will draw excessive current and in some case overheat the BC337.
The main problem is when using a different photo diode to the SFH2030. Any other photo diode LED should
work, but you need to know its operating wavelength range beforehand. This will generally be described
in the manufacturers data sheet or possibly described if you order from an electronic component catalogue.
With these last two points in mind, you should be rewarded with a useful and working circuit.
This has been very kindly drafted by Domenico from Italy. First the copper side:
A magnified view from the component side is shown below. Unfortunately the transistor outline was reversed in the original diagram,
my thanks go to Federico Laura for correcting this diagram :
Mark 1A Version
The modification to the Mark 1 circuit is shown below. This Mark 1A circuit has improved noise immunity to daylight and mains powered lighting. The
22n capacitor has a high impedance at 50/60Hz and daylight but allows a modulated control signal to pass. Under quiescent (no signal conditions)
the 2N2222 transistor is forward biased via the 22k base resistor. This means that the BC337 will be in cut-off and no output from either LED.
A remote control signal will modulate the 2N2222 transistor at the frequency of the IR control (usually 38kHz), which in turn is amplified by
the BC337. As this is a cleaner signal, the series resistor (27 ohm in Mark 1) is increased to 100ohms.
Finally below, a neat and compact cased version of the Mark1 circuit, completed by Nick from UK.
Mark 1A Construction Tips
Below are some helpful hints from one of my viewers in Michigan, USA. Michael Coraci had a few problems with the Mk 1A version , which he solved. If you have trouble, try the following:
1) SH2030 diode was installed backward , this was an easy fix cause I used two pins of a 3 pin transistor socket instead of soldering the diode in place, it was easily reversed but the circuit still wouldn't work.
2) Was using a 120 Vac to 12 Vdc 300ma plug in transfomer that was putting out 16.8 Vdc. CHANGED this to a 9 Vdc 350ma unit that put out 13.0 Vdc
and the unit worked just fine.
(You may want to include on your site that the extender is very sensitive to input voltage. I read on your site of someone else that had a similar
problem and this was the corrective action.) Michael's MK1A is below:
Mark 1A Setup Tips
These tips are again from Michael and how he uses his Mk 1A extender circuit:
1) LED 0 (the remote diode) is placed approximately 40 feet (12.5 meters) away from the actual circuit in the bedroom. I used an 18 SWG two wire
from the main circuit to LED 0 at the cable box.
2) the Extender Circuit receives the signal from about 5 meters away and channels change easily.
3) I have found out tha the Mark1A is light sensitive and in the future I will update it to the Mark 5 version but for now we only use the device
in the evening and ambient light doesn't seem to be a problem.
Last revision 24 May 2010